layiq

/la·yiq/adjective

worthy; deserving; fitting; suitable.

A role, opportunity, or path that merits attention, time, and pursuit.

Sr. Electromechanical Assembly & Test Technician at Blue Origin | LAYIQ

Electrical build and test
Fabricating and installing power and control wiring per wiring diagrams, schematics, and cable schedules, including crimping, ferruling, lugging, soldering, and labeling
Terminating high-current conductors and fabricating, bending, and installing bus bar assemblies, with bolted joints torqued to specification
Applying insulation systems, including taping, sleeving, resin or varnish impregnation, potting, and encapsulation
Building and wiring control, instrumentation, and protection panels, and routing cable in conduit, tray, and flex with proper strain relief, grounding, and shield terminations
Setting up and running electrical and electronics tests per written procedures, including test article hookup, instrumentation installation, and verifying the setup before energizing
Performing electrical verification and acceptance testing, including continuity and ringout, low-resistance measurement, insulation resistance (megger), hipot or dielectric withstand, polarity verification, and functional checkout, recording results against pass/fail criteria
Troubleshooting failures to the assembly, board, component, or wiring level and performing approved rework including component-level soldering, using proper ESD practices
Operating bench and stand test equipment such as multimeters, oscilloscopes, power supplies, current clamps, insulation testers, dielectric withstand testers, and data acquisition systems
Mechanical assembly and integration
Performing precision mechanical assembly, including fits and clearances, shimming, alignment, press and interference fits, and fasteners torqued to specification
Integrating electrical and mechanical sub-assemblies into higher-level units through final assembly, closeout, and preparation for acceptance test
Operating shop and material handling equipment including overhead cranes and rigging, and performing dimensional and electrical inspection with calipers, micrometers, dial indicators, DMMs, megohmmeters, and low-resistance ohmmeters
Preparing and verifying kits to the bill of materials, confirming material traceability, and helping ready new stations for production
Quality and safety
Following work instructions and test procedures precisely and recording completed steps and in-process data as required
Escalating problems found at the bench, including incorrect instructions, drawing discrepancies, tooling issues, and quality, safety, or material concerns, and supporting discrepancy disposition
Training and checking the work of less-experienced technicians, and working safely around energized and high-energy equipment including lockout/tagout and arc flash PPE

Experience building or wiring high-current electrical assemblies in a regulated or high-reliability environment such as aerospace, defense, solar, marine, rail, or precision industrial manufacturing
Bench testing, checkout, or troubleshooting of electronic assemblies, PCBAs, or control hardware, including component-level soldering and board rework
Executing formal acceptance test procedures and documenting results, including insulation resistance, hipot or dielectric withstand, or low-resistance testing
Insulation systems and processes, including Class F/H materials, taping and sleeving, and resin or varnish impregnation
Sensor and instrumentation installation and checkout, or PLC and control system I/O troubleshooting
Military or commercial electronics technician background, or formal electrical or electronics training through apprenticeship, technical school, or military program
Certification to IPC/WHMA-A-620, IPC-A-610, J-STD-001, or an equivalent workmanship standard, plus ESD control training (ANSI/ESD S20.20) and NFPA 70E arc flash training
Experience in a new or start-up production environment where processes, tooling, and documentation were still being developed, working to documented quality standards including configuration control and traceability
Culture Statement
Don’t meet all desired requirements? Studies have shown that some people are less likely to apply to jobs unless they meet every single desired qualification. At Blue Origin, we are dedicated to building an authentic workplace, so if you’re excited about this role but your past experience doesn’t align perfectly with every desired qualification in the job description, we encourage you to apply anyway. You may be just the right candidate for this or other roles.
Export Control Regulations
Applicants for employment at Blue Origin must be a U.S. citizen or national, U.S. permanent resident (i.e. current Green Card holder), or lawfully admitted into the U.S. as a refugee or granted asylum.
Background Check
Required for all positions: Blue’s Standard Background Check
Required for Certain Job Profiles: Defense Biometric Identification System (DBIDS) background check if at any time the role requires one to be on a military installation
Required for Certain Job Profiles: Drivers who operate Commercial Motor Vehicles with a Gross Vehicle Weight (GVW), Gross Vehicle Weight Rating (GVWR) or combination of power unit and trailer that meets or exceeds 10,001 lbs. and/or transports placardable amounts of hazardous materials by ground in any vehicle on a public road while in commerce, may be subject to additional Federal Motor Carrier Safety Regulations including: Driver Qualification Files, Medical Certification (obtained before onboarding), Road Test, Hours of Service, Drug and Alcohol Testing, vehicle inspection requirements, CDL requirements (if applicable) and hazardous materials transportation/shipping training.
Required for certain Job Profiles: Ability to obtain and maintain Merchant Mariner Credential, which includes pre-employment and random drug testing as well as DOT physical

Benefits

Benefits include: Medical, dental, vision, basic and supplemental life insurance, paid parental leave, short and long-term disability, 401(k) with a company match of up to 5%, and an Education Support Program.
Stock Options for all regular employees (working at least 20 hours/week)
Paid Time Off: Up to four (4) weeks per year based on weekly scheduled hours, and up to 14 company-paid holidays.
Dependent on role type and job level, employees may be eligible for benefits and bonuses based on the company's intent to reward individual contributions and enable them to share in the company's results, or other factors at the company's sole discretion. Bonus amounts and eligibility are not guaranteed and subject to change and cancellation. Please check with your recruiter for more details.
Equal Employment Opportunity
Blue Origin is proud to be an Equal Opportunity/Affirmative Action Employer and is committed to attracting, retaining, and developing a highly qualified and dedicated work force. Blue Origin hires and promotes people on the basis of their qualifications, performance, and abilities. We support the establishment and maintenance of a workplace that fosters trust, equality, and teamwork. We provide all qualified applicants for employment and employees with equal opportunities for hire, promotion, and other terms and conditions of employment, regardless of their race, color, religion, sex, sexual orientation, gender identity, national origin/ethnicity, age, physical or mental disability, genetic factors, military/veteran status, or any other status or characteristic protected by federal, state, and/or local law. Blue Origin will consider for employment qualified applicants with criminal histories in a manner consistent with applicable federal, state, and local laws, including the Washington Fair Chance Act, the California Fair Chance Act, the Los Angeles Fair Chance in Hiring Ordinance, and other applicable laws. For more information on “Know Your Rights,” please see here .
Affirmative Action and Disability Accommodation
Applicants wishing to receive information on Blue Origin’s Affirmative Action Plans, or applicants requiring a reasonable accommodation in order to participate in the application and/or interview process, please contact us at EEOCompliance@blueorigin.com . Please note this is a publicly managed inbox. Please do not include any personal medical information in your request.

Sr. Electromechanical Assembly & Test Technician

Employer job description

Application close date:

Responsibilities include but are not limited to:

Minimum Qualifications:

Preferred Qualifications:

Benefits

About this listing